Committed to becoming a technical expert and leader in the field of industrial communication bus interconnection
GYLP-8596-03，10Gbps 300m Duplex LC SFP Transceiver
We support OEM & ODM orders. Please feel free to contact with us if you need.
- Product Description
- Specification Parameters
- Product Dimensions
- Installation Instructions
- Equipment Grounding
- Power Connection
- Ordering Information
-
- Commodity name: GYLP-8596-03，10Gbps 300m Duplex LC SFP Transceiver
Features
Supports 10Gbps serial optical interface
850nm VCSEL Laser and PIN photo-detector
Up to 300m on 50/125µm MMF(OM3)
Duplex LC receptacle optical interface compliant
Hot pluggable
All-metal housing for superior EMI performance
RoHS6 compliant (lead free)
Operating case temperature:
Commercial: -5ºC to +70°C
Applications
10GBASE-SR/SW
Other optical links
Standards
Compliant with SFP+ MSA
Compliant with SFF-8472
Compatible with IEEE802.3ae
Description
The SFP+ SR transceivers are designed for use in 10-Gigabit Ethernet links up to 300m over Multimode Mode Fiber (OM3).
-
Maximum Supported Distances
Fiber Type
Minimum modal bandwidth@850nm
Min.
Typical
Max.
Unit
62.5µm MMF
160MHz*km
2
26
m
OM1:200MHz*km
2
33
m
50µm MMF
400MHz*km
2
66
m
OM2:500MHz*km
2
82
m
OM3:2000MHz*km
2
300
m
OM4:4700MHz*km
2
400
m
The transceivers are compatible with SFP+ MSA and SFF-8472. For further information, please refer to SFP+ MSA and SFF-8472.
Module Block Diagram
Absolute Maximum Ratings
Parameter
Symbol
Min.
Typical
Max.
Unit
Power Supply Voltage
VCC
0
3.6
V
Storage Temperature
Ts
-40
+85
°C
Relative Humidity
RH
5
85
%
RX Input Average Power
Pmax
-
1.5
dBm
Recommended Operating Environment
Parameter
Symbol
Min.
Typical
Max.
Unit
Power Supply Voltage
VCC
3.13
3.3
3.46
V
Power Supply Current
ICC
300
mA
Operating Case Temperature
Commercial
TC
-5
+70
°C
Data Rate
10.3125
Gbps
Electrical CharacteristicsParameter
Symbol
Min.
Typical
Max.
Unit
Note
Transmitter Section
Input Differential Impedance
Rin
90
100
110
Ω
Differential Data Input Swing
Vin PP
180
700
mV
1
Transmit Disable Voltage
VD
Vcc – 1.3
Vcc
V
Transmit Enable Voltage
VEN
Vee
Vee+ 0.8
V
Receiver Section
Differential Data Output Swing
Vout PP
300
850
mV
LOS Fault
Vlos fault
Vcc – 0.5
Vcc_host
V
2
LOS Normal
Vlos norm
Vee
Vee+0.5
V
2
Notes:
1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
2. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of signal is logic 1.
Optical Parameters
Parameter
Symbol
Min.
Typical
Max.
Unit
Note
Transmitter Section
Centre Wavelength
λc
840
850
860
nm
Spectral Width (RMS)
σ
0.45
nm
Average Optical Power (avg.)
Pout
-6.5
-1
dBm
1
Laser Off Power
Poff
-
-
-30
dBm
Extinction Ratio
ER
3.0
5.0
-
dB
2
Relative Intensity Noise
RIN
-
-
-128
dB/Hz
Optical Rise/Fall Time
tr / tf
-
50
ps
3
Optical Return Loss Tolerance
-
-
12
dB
Output Optical Eye
Compliant with IEEE802.3ae eye masks when filtered
2
Receiver Section
Receiver Center Wavelength
λc
840
860
nm
Receiver Sensitivity
Sen
-
-
-11.1
dBm
4
Stressed Receiver Sensitivity(OMA)
Sens
-
-
-7.5
dBm
Los Assert
LOSA
-30
-
-
dBm
Los Dessert
LOSD
-
-
-13
dBm
Los Hysteresis
LOSH
0.5
-
5
dB
Overload
Pin-max
-
-
-1
dBm
4
Receiver Reflectance
-
-
-12
dB
Receiver power (damage)
-
-
1.5
dBm
Notes:
1. The optical power is launched into 50/125µm MMF.
2. Measured with a PRBS 231-1 test pattern @10.3125Gbps.
3. Unfiltered, 20-80%. Measured with a PRBS 231-1 test pattern @10.3125Gbps.
4. Measured with a PRBS 231-1 test pattern @10.3125Gbps, ER=4dB, BER <10-12.
Timing Characteristics
Parameter
Symbol
Min.
Typical
Max.
Unit
TX_Disable Assert Time
t_off
100
us
TX_Disable Negate Time
t_on
2
ms
Time to Initialize
t_start_up
300
ms
Tx_Fault Assert
t_fault_on
1
ms
Tx_Fault Reset
t_reset
10
us
Rx_LOS Assert Delay
t_los_on
100
us
Rx_LOS Negate Delay
t_los_off
100
us
Clock Frequency
fSCL
0
400
kHz
Digital Diagnostic Monitor Characteristics (DDM)
The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode. For external calibration mode please contact our sales stuff.
Parameter
Symbol
Min.
Max.
Unit
Temperature Monitor Absolute Error
DMI_Temp
-3
3
°C
Laser Power Monitor Absolute Error
DMI_TX
-3
3
dB
RX Power Monitor Absolute Error
DMI_RX
-3
3
dB
Supply Voltage Monitor Absolute Error
DMI_VCC
-3%
3%
V
Bias Current Monitor Absolute Error
DMI_Ibias
-10%
10%
mA
Digital Diagnostic Memory Map (Compliant with SFF-8472)
The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.
The digital diagnostic memory map specific data field defines as following (For further information, please refer to SFF-8472).
Pin Definitions
Pin Descriptions
Pin
Signal Name
Description
Plug Seq.
Notes
1
VeeT
Module Transmitter Ground
1
1
2
TX FAULT
Module Transmitter Fault
3
3
TX Disable
Transmitter Disable; Turns off transmitter laser output
3
4
SDA
2-Wire Serial Interface Data Line
3
2
5
SCL
2-Wire Serial Interface Clock
3
2
6
Mod_ABS
Module Definition, Grounded in the module
3
7
RS0
Receiver Rate Select (not used)
3
8
LOS
Receiver Loss of Signal Indication Active LOW
3
9
RS1
Transmitter Rate Select (not used)
3
10
VeeR
Module Receiver Ground
1
1
11
VeeR
Module Receiver Ground
1
1
12
RD-
Receiver Inverted Data Output
3
13
RD+
Receiver Non-Inverted Data Output
3
14
VeeR
Module Receiver Ground
1
1
15
VccR
Module Receiver 3.3 V Supply
2
16
VccT
Module Transmitter 3.3 V Supply
2
17
VeeT
Module Transmitter Ground
1
1
18
TD+
Transmitter Non-Inverted Data Input
3
19
TD-
Transmitter Inverted Data Input
3
20
VeeT
Module Transmitter Ground
1
1
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1. Module ground pins GND are isolated from the module case.
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
-
Recommended Power Interface Circuit
Recommended Interface Circuit
Mechanical Dimensions
-
Part Number
Product Description
GYLP-8596-03
850nm, 10Gbps,MMF 300m, Duplex LC SFP+ Transceiver, -5ºC ~ +70ºC, With DDM.
Key words:
GYLP-8596-03，10Gbps 300m Duplex LC SFP Transceiver
Series of Products
Get a Free Quote
PLEASE LEAVE YOUR MESSAGE AND WE WILL CONTACT YOU AS SOON AS WE RECEIVE IT!
FAQ
Q
How can I request a tailored solution or contact for business collaboration?
A
Please reach out through our Contact page or send an inquiry to our business team for prompt assistance and customized service offerings.
Q
Does Gengyuan support large-scale network deployments?
A
Yes, our solutions (e.g., 10-gig fiber optic rings) are designed for scalability and self-healing in large networks, ideal for widespread industrial and infrastructure applications.
Q
How does Gengyuan integrate AI into communication solutions?
A
We combine advanced communication bus technology with AI and security features to enable smarter, efficient, and secure industrial interconnectivity.
Q
What kind of technical support and R&D capability does Gengyuan offer?
A
We have full R&D capabilities, over 60 sets of R&D testing instruments, and a 2,000+ square meter production line to ensure product quality and innovation.
Contact Us
Whatsapp：+966 564618242
Phone：+86-15198078772
Address : 4th Floor, Matian Center, No. 15, West Train South Station Road, Wuhou District, Chengdu City, Sichuan Province